Em estoque Produto em alta
UHLAC1
UHLAC1 HLAC1 HL-AC1 PANASONIC HL-T1 sensor controller, NPN, 12-24VDC
$0.00
USD
3192 em estoque
Especificações principais
Item:
Specifications
Type:
NPN output
Weight:
Net weight: 140 g approx.
Details:
Controller (NPN output)
Informações do fornecedor
PANASONIC
Produtos: 4316
Geralmente enviado em 2 a 3 dias úteis.
Qualidade garantida
Envio rápido
Suporte técnico
Especificações técnicas
| Parâmetro | Valor |
|---|---|
| Item | Specifications |
| Type | NPN output |
| Weight | Net weight: 140 g approx. |
| Details | Controller (NPN output) |
| Product | Ultra-compact Laser Collimated Beam Sensor |
| Material | Enclosure: Polybutylene terephthalateTransparent cover: Polycarbonate |
| I/O cable | 0.09 mm210-core composite cable, 2 m6.562 ftlong |
| Part Number | HL-AC1 |
| Reset input | 0 V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Product name | Ultra-compact Laser Collimated Beam Sensor HL-T1 |
| Timing input | 0 V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Linear output | Current / voltage output switchable (Note)-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller. |
| Main functions | ・Measured value display・Setting value, light amount value resolution display・Standard received light setting・Automatic scaling・Scaling・Display reverse・ECO display・Display digits limitation・Sample hold・Peak hold・Bottom hold・Peak to peak hold・Self peak hold・Self bottom hold・Zero reset・Initial reset・ON-delay timer・OFF-delay timer・One-shot timer・Differentiation・Sensitivity selection・Threshold value direct setting・Positioning teaching・2-point teaching・Automatic teaching・Hysteresis width variability・Monitor focus・Non-measuring time setting・(A – B) calculation(Note：The calculation unit is necessary.)・(A + B) calculation(Note：The calculation unit is necessary.)・Mutual interference prevention (Note：The calculation unit is necessary.)・Laser deterioration detection・Key lock・Zero reset memory |
| Product Number | HL-AC1 |
| Supply voltage | 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less |
| Laser OFF input | 0 V connection: Laser emission haltOpen: Laser emission-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Measuring cycle | 150 micro s |
| Pollution degree | 3 (industrial environment) |
| Zero reset input | 0 V connection: Zero reset operatesOpen: Zero reset ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Current consumption | 190 mA or less (when connected to the sensor head) |
| I/O cable extension | Extension up to total 10 m32.808 ftis possible, with 0.09 mm2or more, cable.(Note) If the extension cable is longer than 10 m32.808 ft, then it will not qualify for CE marking. |
| Sub-digital display | 5 digit yellow LED display[RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.] |
| Main digital display | 5 digit red LED display[RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.] |
| Insulation resistance | 20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure |
| Applicable sensor head | HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F |
| Voltage withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| Indicators : Enable (ENABLE) | Green LED (lights up during normal operation) |
| Indicators : Judgment outputs | HIGH: Orange LED (lights up when measured value > HIGH threshold value)PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value)LOW: Yellow LED (lights up when LOW threshold value > measured value) |
| Indicators : Zero reset (ZERO) | Green LED (lights up when the zero reset function is enabled) |
| Settable average sampling rate | 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1). |
| CE marking directive compliance | EMC Directive, RoHS Directive |
| Judgment outputs (HIGH, PASS, LOW) | NPN open-collector transistor-Maximum sink current: 50 mA-Applied voltage: 30 V DC or less (between judgment output and 0 V)-Residual voltage: 1.2 V or less (at 50 mA sink current) |
| Indicators : Laser emitting (LD ON) | Green LED (lights up during laser emission) |
| Environmental resistance : Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Environmental resistance : Shock resistance | 300 m/s2acceleration (30 G approx.) in X, Y and Z directions three times each |
| Linear output : Temperature characteristics | plus or minus 0.2 % F.S./℃(Note) These are the temperature characteristics of the linear output when the sensor head is connected. |
| Environmental resistance : Ambient temperature | 0 to +50 ℃+32 to +122 ℉(No dew condensation allowed), Storage: -25 to +65 ℃-13 to +149 ℉ |
| Environmental resistance : Vibration resistance | 10 to 150 Hz frequency, 0.7 mm0.028 indouble amplitude in X, Y and Z directions for 80 min. |
| Judgment outputs (HIGH, PASS, LOW) : Output operation | HIGH: ON when measured value > HIGH threshold valuePASS: ON when HIGH threshold value >= measured value >= LOW threshold valueLOW: ON when LOW threshold value > measured value |
| Judgment outputs (HIGH, PASS, LOW) : Number of outputs | HIGH / PASS / LOW 3 values output |
| Judgment outputs (HIGH, PASS, LOW) : Utilization category | DC-12 or DC-13 |
| Judgment outputs (HIGH, PASS, LOW) : Short-circuit protection | Incorporated |
Descrição do produto
HLT1 Series Controller, 12-24 VDC Power, NPN Digital Output, Selectable Analog Output between 4-20mA and ±4V
Principais características
- Qualidade de nível industrial
- Em conformidade com a RoHS
- Certificado CE
- Garantia de 1 ano
Documentos do produto
Ficha de dados
Especificações técnicas e dados de desempenho
Manual do Usuário
Guia de instalação e operação
